Friday 31 March 2017

Upgrades and changes to the BCN3D Sigma 3D Printer including Bondtech extruders


SIGMA v2016 3D Printer upgrades, changes and tweaks

In this blog post I'm collecting up all the modifications, changes, upgrades and general improvements I have done to the Sigma (2016 version) over the last ~18 months.

This blog post and video is for the Sigma 2015/16 versions, and may not be the same for the new Sigma R17 (2017 model).


A lot of the information here is also relevant for any 3D printer, things to check, changes to make and improvements.

The main goals were to improve complex print performance - especially dual colour or dual material 3D Printing on Sigma, and also to reduce the noise.

Thank you to the team at BCN3D for the allowing me to test out some of the upgrade boards in this machine, and also to Emvio Engineering and Bondtech for the dual drive Extruder upgrade kit.

All the info is in the video below, and feel free to use the quick jump point index if there is something you specifically want to know about -

Quick jump index -
00:10 - Intro to Sigma 2016 changes
02:20 - Auto Fan control for hot-ends
04:30 - Hot-end Thermistor changes (PTFE removal)
07:50 - Adding heatsink compound to Hot-ends
12:10 - Fitting Bondtech Extruders to Sigma
16:00 - Updating Firmware eSteps/mm for Extruders
17:10 - Printing with Sigma and Bondtech extruders
18:00 - Further thoughts on testing and upgrades
19:00 - Compare print results
Final thoughts and wrap-up.


Video is also over on YouTube if you wish to watch in HD and also subscribe to my channel for more videos, help and advice.

I'll post a few images below as they are easier to see than in the video. My thoughts and advice are in the video so I'll keep the post short and look forward to any comments or questions - feel free to post here or in the YouTube comments. Thanks.

In the video I look at a number of significant changes Including -

Automatic fan speed control for both hot-ends -



Hot end improvements -

I replace the original hot-end thermistor sleeves (PTFE Max temperature 250 Deg C) with Fibreglass (300+ Deg C)


Still using the grub-screw to clamp for now, but I comment on why this is not really a good idea.


 I show you how to remove the Hot-ends and improve their thermal performance by adding thermal heatsink compound.



I then fit Bondtech dual drive Extruders into Sigma and compare print results.



In all comparison testing I used exactly the same Gcode for both system configurations of extruders (just the eStep/mm setting was changed in firmware for the new Bondtech gear rate).

The Hollow Draudi printed small with standard 0.4mm nozzles is a very tricky small print for FFF 3D printers - Designed by BCN3D

You can get the file here from Youmagine.

"The Hollow Draudi is designed to be created on resin 3D printers mainly due to their empty geometry. In addition, all orifices, modeled with Rhinoceros and Grasshopper, give it a unique personality and a plus of difficulty that will challenge any 3D printer FFF."



This is a tricky print - the extruders need some tweaking, but even with exactly the same Gcode used we can see less stringing and better formed structures between the holes.



Smoother extrusion on the feet - easier to see on the Brim rings - less indications of the individual extruder stepping points on the Bondtech print.



Low-Poly Bulbasaur - Multi and Dual Extrusion version - by- Agustin Flowalistik

Get this great 3D model from Youmagine here


Smoother extrusion and less problems with filament control here using the Bondtech extruders.

And yes, I know you can get better results out of the Sigma, by slowing down the print speed and being slightly less aggressive with the extruder settings, but I wanted to do a like-for-like comparison of exactly the same Gcode here to show the difference a gearbox and dual drive teeth make to a 3D printers extrusion system.

Sigma 2017 -

I also now have the new Sigma R17 machine now, so do keep an eye out for another comparison of the above tests along with the new Sigma R17 version.



If you have a Sigma 3D printer and need any help or advice, please catch me on twitter and I'll do my best to help out. I have been printing with Sigma for a few years now and have (I think) mastered using it for single and dual colour/material printing. It's my go-to printer for all dual 3Dprinting.

I'm really excited for the new Sigma 2017 and can't wait to show you what it can do.

Thank you for reading & watching, see you next time.


Rich.

Please join me on Twitter @RichRap3D   -  https://twitter.com/RichRap3D

Files and designs shared on YouMagine - https://www.youmagine.com/users/richrap

Files and designs shared on GitHub – https://github.com/RichRap

Files and designs shared on Repables - http://repables.com/u/richrap/

My Youtube channel is here, all 3D Printing and Hi-Def video content.


Monday 13 March 2017

Using the LulzBot TAZ 6 3D Printer - Part 1 Setup


TAZ 6

LulzBot are without doubt (in my opinion) the most open-Source 3D Printing company in the world.

Here is the start of my journey with the TAZ 6 3D Printer.
I could spend an entire blog post just telling you how LulzBot have open-source in every single aspect of their business. Not just the 3D printers they design, develop, support and manufacture, but all the systems they use, computers running them and well just everything. If someone told me they only drank open-source coffee? I would not be surprised in the slightest.

To the point they will contact independent developers (anywhere in the world) and help them finish, refine and improve a little-known open-source software package, because they would like to use it in their business too.

Just have a poke around on the LulzBot development site if you want to be impressed by Openness - http://devel.lulzbot.com/

LulzBot (and the Parent company Aleph Objects inc.) support many independent projects and diverse developments, they don't always shout about it, they just get involved and encourage. If I lived in the USA I would be camping out at LulzBot HQ.

We need to see more of these manufacturers in an amazing community like 3D Printing. I hope LulzBot always manage to stay that way. Anyway, enough of that. You can see I have a lot of time for the LulzBot team, their products and everything they stand for.

My admiration of LulzBot is not going to stop me from a detailed (and sometimes critical) look at their 3D Printers, software and generally the user experience with all of it. They thrive on all feedback and it's one of the fundamental aspects of open-innovation, so here we go with a first look at the LulzBot TAZ 6 3D Printer.

I'm not going to attempt to 'sell you' on this 3D printer. It's been out for a while and has already won awards on 3D Hubs and has a good reputation in the 3D printing community. You can make your own mind up about the machine. See if it's right for you and at the price point and feature list you need.

I'm not even going to go into detailed specifications about print size or capacity, you can google that or just look on the LulzBot website. I'm going to focus on the experience and how reliable it is over a long period of use and abuse in the real-world and how it handles lots of different materials.


I hope to be able to show you what it can and can't do over this and more blog posts and video's. If you have any questions or want me to try something specific, just send me a message (twitter is best, but anything usually works - apart from carrier pigeon).

If you watch the first video below (it's long, but I make no apology for that) you will see that you get a really good first experience with unboxing, assembly and setup of the TAZ 6.

I hardly ever do 'unboxing' video's, but this machine just deserved a showcase.


Quick jump index -
01:28 - Materials
03:35 - Unboxing the TAZ 6
06:15 - MOARstruder ???
12:30 - Approvals, regulations, safety
17:00 - Taz 6 Assembly
28:50 - Power ON...
30:30 - Handheld Gaming (3D printed)
32:55 - In the next TAZ 6 Video

I have always been a huge fan of the LulzBot 3D printers, I printed out and built up one of the very early prototype TK-0 machines back in 2013 (an early version of the TAZ design) I made many modifications and eventually dedicated my variant as a portable machine to use at shows and events.

During discussions after the TCT Show in 2016, the team from LulzBot kindly offered to send me a TAZ 6. This is not only great, but as it's a machine that is not normally seen in the UK / Europe I really want to help support the growth and awareness of LulzBot products (and their open-source / Open-Innovation nature).


I did have some initial setup problems, I will go into detail in Part 2 of this blog post and video series.

A pesky dislodged connector caused me some initial setup problems, but it was quickly identified and resolved. Much more about the problems, issues and resolutions in the next video / blog post - along with lots of 3D Prints and feedback about both print quality and user experience.

LulzBot also sent me over some materials that are tricky to find over in the UK or Europe. These have been really great to try out and do work exceptionally well in this 3D printer.

 LulzBot standard ABS Filament.

 Chroma Strand Labs Inova-1800 Co-Polyester.

 The only Taulman3D material I had yet to try out - Taulman n-vent
 And Verbatim PLA.

LulzBot also included some sample filament in the TAZ 6 Box. This is what you would get if you just ordered the printer - Very nice filament from Proto-pasta and Colorfabb.


Initial assembly is very straightforward, a detailed manual guides you through all the steps and provides great advice along the way.




Every single part (including the full set of tools provided) feels high quality and 'engineered' to a fine level.


I talk a lot about the approvals and regulations for this 3D printer in the video (it's a very good thing). I'm not going to repeat myself here, but do watch the part about 3D printer approvals (12:30 onwards) as it's good to know why fully assembled, well designed and tested machines are worth the extra cost etc.


Noise level is acceptable during setup and also full operation. It's around the same overall noise level as a Prusa i3 MK2 (normal setting) the Prusa quiet setting is slightly lower. The TAZ6 has a lower frequency to it's noise level output (slightly bigger fans than many 3D printers) so feels less annoying and less distracting in the background. The TAZ 6 is a lower overall noise level than the BCN3D Sigma (2016 version).

I have no problem with the TAZ 6 running in the same small room when I'm 1.5M away from it.

 Bucket O' Octopi by yeoldebrian, published 

A test print Octopus (Above) was included, I had no problems replicating and exceeding this print quality with the Taz 6.


We did plenty of  'play printing' over Christmas, lots of the standard objects, test prints and plenty of decorations. When it was all dialled in I started to explore what the TAZ 6 could really achieve.


The Red Chroma Strand Labs filament was really nice to use, and strong. I designed and printed some hooks for hanging objects to rafters, they were clean prints (just look at those perfect layers) and very strong indeed. I'll see if I can work out a way to break these and compare the results with PLA or ABS for the next blog post.


It was not long before 17+ hour prints were being tested and then multi-day objects in ultra fine and full build area dimensions. (more on that next time).


As default it is set to print quite slowly. The default profiles for Cura have a low speed of travel rate, it can handle a lot faster. The firmware (Marlin) acceleration feels slower than my normal settings. There is nothing wrong with going a little slower and having a lower acceleration, in fact it can improve both print quality and further reduce noise level.

The issue is more with the fact this printer can print BIG, so really you are going to need a compromise of both speed and quality for some bigger prints if you want them to finish in a working day or before going to bed. That's no different to many 3D printers, so this issue is not aimed at the TAZ, just an observation with bigger build areas in general.

LulzBot have installed a 0.5mm nozzle as standard. This provides a a good mix of speed v quality in many types of printed model. The original RepRap 'standard nozzle size' was 0.5mm, but over the last five+ years it's now much more common to see a 0.4mm being fitted to almost all 3D printers.

You could replace the nozzle, but if anything I may decide to go even bigger, this machine is just crying out for a great big nozzle to produce some serious 3D prints fast and accurately. And on that point I had hoped to be testing out the now MOARstruder, but sadly it was not quite available when I asked about it.  (see below).

MOARstruder is now fully available for the TAZ5 and TAZ6 directly from LulzBot on the website, you can check it out here.

After a lot more printing and testing with the TAZ6 Hexagon hot-end, I'm probably going to make a new extruder for the TAZ6 using the E3D Volcano. The Volcano is very similar to the new MOARstruder, in fact the nozzles are interchangeable for the Volcano ones, so you can fit hardened, stainless, brass or copper types.

In the next LulzBot TAZ 6 blog post (and video) will go into a lot more detail about the print quality, settings and use of both Cura and other slicing engines on the TAZ 6.

The TAZ6 did a lot of printing towards the end of 2016 and over Christmas. I now feel I understand many of the limits and balance between quality and settings for this 3D Printer. I significantly tweaked the profiles and then also stopped using Cura. It's producing solid and consistent results and has handled all materials I have thrown at it.

This 3D Printer is a very well engineered (slightly over-engineered, but in all good ways). It feels solid and always in control, the bed-level system is low-tech, but reliable and more importantly it works really well.


I'm totally enjoying the 3D printing experience with the TAZ 6. Plenty of things I would (and will) change, but for an out-of-the-box experience, it's delightful from delivery to first print (apart from the issue I had, but more on that next time). I have a lot more feedback for anyone considering this 3D printer, so join me text time for a closer look at the prints, profiles and capability of the LulzBot TAZ 6.

I almost forgot, in the video I talk about a Handheld Retro Gaming PC system I made up (Windows 10 to emulate older games and the like) - it was a simple and fun 3D printing project (anyone could do), I'm happy to go into a lot more detail, let me know if anyone would find this sort of project interesting. I do a lot of projects using 3D printing and often electronics / Arduino etc. - Not really sure if I should post more of these here or not?



Not printed on the TAZ 6, but I found it and talked about this project in the TAZ 6 video above, let me know if you want to see more projects (and maybe a design / assembly guide?) on these sort of things.







This was just a brief introduction to the TAZ 6 experience. Lots more next time, I hope you enjoyed it.

Rich.
@Richrap3D
RichRap on Youtube